Henan Doing Mechanical Equipment Co.,Ltd
We are an integrated manufacturer for research and develop, production and sales of pelletizing machine .

Description of the Pelleting Process

Description of the Pelleting Process :

The process of manufacturing fuel pellets involves placing ground biomass under high pressure and forcing it through a round opening called a “die.” When exposed to the appropriate conditions, the biomass “fuses” together, forming a solid mass. This process is known as “extrusion.” Some biomass (primarily wood) naturally forms high-quality fuel pellets, while other types of biomass may need additives to serve as a “binder” that holds the pellet together. However, the creation of the pellets is only a small step in the overall process of manufacturing fuel pellets. These steps involve feedstock grinding, moisture control, extrusion, cooling, and packaging. Each step must be carried out with care if the final product is to be of acceptable quality.

Raw Material for pelleting process :
The production of wood pellets begins with the generation of the raw material. In most cases this raw material is a byproduct of some other wood processing operation. Hardwood flooring mills are one example: They produce large quantities of clean (no bark or dirt), dry sawdust and small scrap blocks in their operations. This byproduct makes an ideal raw material for pellet production; however, as the interest in pellet production grows, some mills are generating pellet-making raw materials directly from trees (i.e. “roundwood”).

Feedstock Grinding for pelleting process :

Standard-sized pellet mills generally require biomass that is ground to particles that are no more than 3 millimeters in size. Several types of equipment are available to carry out this task. If the biomass is quite large and dense (e.g., wood), the material is first run through a “chipper,” and then run through a hammer mill or similar device to reduce the particles to the required size. Smaller and softer biomass (e.g., straw) can be fed directly into the hammer mill without first being chipped.
Moisture Control for pelleting process :

Maintaining an appropriate moisture level in your feedstock is vital for overall quality of the final pellets. For wood, the required moisture level of the feedstock is at or near 15 percent. Other types of biomass have other requirements—you may need to experiment a bit. Moisture can be removed from the feedstock by oven-drying or by blowing hot air over or through the particles. If the feedstock is too dry, moisture can be added by injecting steam or water into the feedstock.

Extrusion for pelleting process :

The pellet is actually created in this step. A roller is used to compress the biomass against a heated metal plate called a “die.” The die includes several small holes drilled through it, which allow the biomass to be squeezed through under high temperature and pressure conditions. If the conditions are right, the biomass particles will fuse into a solid mass, thus turning into a pellet. A blade is typically used to slice the pellet to a predefined length as it exits the die. Some biomass tends to fuse together better than other biomass. Sawdust is an especially suitable feedstock for pelleting because the lignin that is naturally present in the wood acts as a glue to hold the pellet together. Grasses tend to not fuse nearly as well, and the resulting pellets are less dense and more easily broken. The proper combination of input material properties and pelleting equipment operation may minimize or eliminate this problem. It is also possible to add a “binder” material to the biomass to help it stick together, or to mix a fraction of sawdust, with similar results. Distillers Dry Grains (a product of the corn ethanol industry) are reported to improve the binding properties of some biomass.

Cooling for pelleting process :

Pellets, as they leave the die, are quite hot (~150°C) and fairly soft. Therefore, they must be cooled and dried before they are ready for use. This is usually achieved by blowing air through the pellets as they sit in a metal bin. The final moisture content of the pellets should be no higher than 8 percent. Packaging for pelleting process :

Once the pellets are formed and cooled, they are packaged in bags or stored in bulk. Pellets can be stored indefinitely but they must be kept dry to prevent deterioration.

Energy Requirements for Pellet Manufacture

Pellet manufacture requires quite a bit of energy, both for drying damp feedstock and for running the various pieces of machinery. Large plants typically burn a portion of their feedstock to provide heat for drying, whereas smaller facilities often use other means. As a rule of thumb, a pelletizer requires between 50 and 100 kilowatts of electrical demand for every ton per hour of production capacity. In addition, electricity is usually needed to operate any chopping, grinding, drying, cooling, and bagging equipment that is in use. If a reliable source of electricity is not available, gasoline or diesel-based equipment is available.

---

• Pre:Introduction of biomass pellet mill
• Next:Introduction to Fote Ring Die Wood Pellet Mill

---

Get Support or Price!

If you want to get more information and offer of the equipment,leave us message online,we will reply as soon as possible !

Title:

Name:

Country:

Phone:

Email:

Inquiry:

Send Message